Scaner Canon -problema

#1
EmyLush

Posted 20 January 2005 - 19:10

Junior Member

Grup: Members
Posts: 105
Înscris: 11.08.2004

Sal

Am o problema la un Scaner Canon D646U ex :
am instalat scanerul corect si cand dau sa scaneze o imagine imi da aceasta eroare:
Realease the lock switch, detach the USB cable and reconnect. Close the scanner driver.
cred ca zice de un buton de desuptul scanerului care l-am pus la neloked "la lacatul deshis cum arata acolo

" si tot aceea eroare imi da !!
ma puteti ajuta ??!! sunt f. disperat !!

Back to top

#2
tra_k

Posted 21 January 2005 - 17:58

Member

Grup: Members
Posts: 348
Înscris: 12.11.2004

Nu ai instructiunile de instalare de la scaner? Daca DA, ai urmat toti pasii?

De obicei astea au si o carte tehnica iar pe la final sunt tabele de tratare (remediere) a erorilor. Daca nu (mai) ai manualele, incearca de pe site-ul Canon sa le descarci. Nu se poate sa nu fie tratata eroarea!

Bafta!

Back to top

#3
tra_k

Posted 21 January 2005 - 18:30

Member

Grup: Members
Posts: 348
Înscris: 12.11.2004

Uite ce am gasit referitor la eroarea ta:

Quote

Category : Error message
Description : Release the lock switch, detach the USB cable and reconnect. Scanner driver will be closed.

The lock switch holding the carriage assembly is not released properly. Disconnect the USB cable, move the lock switch to the unlocked position and re-connect the USB cable. If the error message still displays even after the lock switch is properly released, the scanner may be defective. Contact your dealer or local Canon Service Center.
02MJ20011_EN_08

Unlocking the Scanning Unit
The lock switch may not be fully unlocked. Check the lock switch, and unlock it if it is not unlocked.
1. Press the power switch to OFF on the scanner or unplug the power cord (USB cable or AC adapter) from the scanner.
2. Move the lock switch to release position.
<If the lock switch is on the bottom of the scanner>
(1) Turn the scanner on its side as shown below.
Note: Do not to turn the scanner over 90 degrees.

Pe adresa de mai jos ai si imaginile aferente:
[edit]

Am pus o alta adresa, prima nu mergea:

http://www.canon.com...leshooting.html

Alegi scanerul tau si apoi bifezi Error. Gasesti acolo mesajul tau de eroare + explicatii.
[\edit]

Edited by tra_k, 21 January 2005 - 19:25.

Back to top

Anunturi

Neurochirurgie minim invazivă

"Primum non nocere" este ideea ce a deschis drumul medicinei spre minim invaziv.

Avansul tehnologic extraordinar din ultimele decenii a permis dezvoltarea tuturor domeniilor medicinei. Microscopul operator, neuronavigația, tehnicile anestezice avansate permit intervenții chirurgicale tot mai precise, tot mai sigure. Neurochirurgia minim invazivă, sau prin "gaura cheii", oferă pacienților posibilitatea de a se opera cu riscuri minime, fie ele neurologice, infecțioase, medicale sau estetice.

www.neurohope.ro

Scaner Canon -problema

#1 EmyLush Posted 20 January 2005 - 19:10

#2 tra_k Posted 21 January 2005 - 17:58

#3 tra_k Posted 21 January 2005 - 18:30

Anunturi

▶ 0 user(s) are reading this topic

Sign In

#1
EmyLush

Posted 20 January 2005 - 19:10

#2
tra_k

Posted 21 January 2005 - 17:58

#3
tra_k

Posted 21 January 2005 - 18:30