Router Juniper NetScreen 5GT
Last Updated: Oct 11 2009 16:05, Started by
ciornav
, Aug 28 2008 15:00
·
0

#1
Posted 28 August 2008 - 15:00

salut
am o problema nu pot sa accesez pentru a configura routerul Juniper NetScreen 5GT pentru a avea internet. Schema conexiunii la internet este: Internet > Modem > Router juniper > switch > calculatoare am gasit pe internet niste imformatie despre acest router insa nu ma ajuta , help please atasez documentul despre juniper Attached Files |
#2
Posted 29 August 2008 - 15:48

salut am o problema nu pot sa accesez pentru a configura routerul Juniper NetScreen 5GT pentru a avea internet. Schema conexiunii la internet este: Internet > Modem > Router juniper > switch > calculatoare am gasit pe internet niste imformatie despre acest router insa nu ma ajuta , help please atasez documentul despre juniper Ce anume nu ai reusit sa faci ? Fi mai explicit. |
#3
Posted 30 August 2008 - 16:47

In pdf-urile puse de tine scrie ca interfata routerului se acceseaza cu 192.168.1.1. Bagi adresa in Internet Explorer si configurezi routerul in functie de conexiunea de internet pe care o ai si in functie de setarile modemului tau.
|
#4
Posted 30 August 2008 - 17:52

Care este providerul tau? RDS, Clicknet etc...
Conectezi routerul la Priza, conectezi si un cablu de retea intre o mufa din pc si una din router, vezi sa nu bagi celalalt capat unde scrie WAN. Setezi ip-ul pe automatic through DHCP apoi deschizi Internet Explorer asa cum spunea driver11 si scrii: http://192.168.1.1 Daca nu te descurci revino cu detalii. |
#5
Posted 01 September 2008 - 10:02

providerul meu este belgacom (sunt in belgia) problema este ca pe 192.168.1.1 este modemul dsl
iar setarile au fost stricate la router si nu-l pot accesa. cum as putea altfel sa-l accesez? Edited by ciornav, 01 September 2008 - 10:03. |
#6
Posted 01 September 2008 - 10:22

Conform USER-GUIDE intre mufa de console si mufa DC adica unde bagi alimentarea e un buton micut reset! Dupa ce l-ai gasit SCOTI modemul din ecuatie, lasi doar un cablu bagat intre pc-ul tau si router (in 1,2,3 sau 4 bagi mufa nu in Untrusted)
Acum urmaresti pasii astia! 1. Locate the reset pinhole on the rear panel. Using a thin, firm wire (such as a paper clip), push the pinhole for four to six seconds and then release. Reset Pinhole The Status LED blinks amber. A message on the Console states that erasure of the configuration has started and the system sends an SNMP/SYSLOG alert. 2. Wait for one to two seconds. After the first reset, the power LED blinks green; the NetScreen-5GT is now waiting for the second push. The Console message now states that it is waiting for a second confirmation. 3. Push the reset pinhole again for four to six seconds. The Status LED lights amber for one-half second, and then returns to the blinking green state. 4. The NetScreen-5GT resets to its original factory settings. When it resets, the Status LED turns amber for one-half second and then returns to the blinking green state. The Console message states that the configuration is erased and the unit is reset. The system generates SNMP and SYSLOG alerts to configured SYSLOG or SNMP trap hosts. 5. The NetScreen-5GT restarts. Sper ca intelegi engleza, oricum pe scurt cu un varf de pix sau orice altceva ce intra acolo tine butonul apasat intre 4-6 secunde Faci o pauza de 2 secunde apoi il tii iar apasat intre 4-6 secunde. apoi intri pe pc, si accesezi http://192.168.1.1 o sa aiba setarile din fabrica, deci userul si parola vor fi netscreen apoi apesi login. |
#7
Posted 01 September 2008 - 10:36

Conform USER-GUIDE intre mufa de console si mufa DC adica unde bagi alimentarea e un buton micut reset! Dupa ce l-ai gasit SCOTI modemul din ecuatie, lasi doar un cablu bagat intre pc-ul tau si router (in 1,2,3 sau 4 bagi mufa nu in Untrusted) Acum urmaresti pasii astia! 1. Locate the reset pinhole on the rear panel. Using a thin, firm wire (such as a paper clip), push the pinhole for four to six seconds and then release. Reset Pinhole The Status LED blinks amber. A message on the Console states that erasure of the configuration has started and the system sends an SNMP/SYSLOG alert. 2. Wait for one to two seconds. After the first reset, the power LED blinks green; the NetScreen-5GT is now waiting for the second push. The Console message now states that it is waiting for a second confirmation. 3. Push the reset pinhole again for four to six seconds. The Status LED lights amber for one-half second, and then returns to the blinking green state. 4. The NetScreen-5GT resets to its original factory settings. When it resets, the Status LED turns amber for one-half second and then returns to the blinking green state. The Console message states that the configuration is erased and the unit is reset. The system generates SNMP and SYSLOG alerts to configured SYSLOG or SNMP trap hosts. 5. The NetScreen-5GT restarts. Sper ca intelegi engleza, oricum pe scurt cu un varf de pix sau orice altceva ce intra acolo tine butonul apasat intre 4-6 secunde Faci o pauza de 2 secunde apoi il tii iar apasat intre 4-6 secunde. apoi intri pe pc, si accesezi http://192.168.1.1 o sa aiba setarile din fabrica, deci userul si parola vor fi netscreen apoi apesi login. merci incerc sa vad daca merge |
#8
Posted 02 September 2008 - 08:16

am facut asa cum mi-ai spus (a trebuit sa astept sa se incheie programul de lucru ) a mers merci mult mult mult
|
#10
Posted 11 October 2009 - 16:05

Redeschid discutia despre juniper 5gt: AM un asemenea router/firewall si 2 conexiuni la internet. Am setat echipamentul in modul dual untrust si vreau sa folosesc in acelasi timp cele 2 legaturi la internet. Am facut sa-mi mearga clintul de DC++ pe o anumita conexiune de internet, uTorrent pe cealalta conexiune de internet cu ajutorul VIP si Policy dupa ce am creat un Custom unde am setat porturile pt fiecare clint in parte.
Ce mai vreau sa fac si nu i-am dat inca de capat....vreau sa pot stabili fiecare calculator(am 2..un descktop si un laptop) din retea sa foloseasca o anumita conexiune la internet pentru navigare si nu cum se intampla acum (cand verific ce ip am in internet imi apare o data IP-ul de la un provider, dupa 10 minute apare IP-ul celuilat ISP si tot asa.....), si sa treaca pe cealalta conexiune disponibila doar in momentul in care apare o defectiune la ISP-ul care il foloseste in mod curent. Ma poate ajuta cineva? |
|
Anunturi
Bun venit pe Forumul Softpedia!
▶ 0 user(s) are reading this topic
0 members, 0 guests, 0 anonymous users