CCNA 1-SBA

Trebuie sa dau saptamana asta ENetwork PT Practice SBA pt CCNA 1 si am primit subiectul de mai jos dar cum, la curs nu prea am facut laboratoare si mai nimic in PT imi cam prind urechile acum... Daca poate cineva sa ma ajute cu rezolvarea raman dator (stiu ca e un fel de copiat dar cum nu prea am facut la cursuri asa ceva acum nu prea am alte variante :| )




Introduction
In this practice Packet Tracer Skills Exam, you will:
 design and implement an addressing scheme to meet stated requirements
 configure, verify, and troubleshoot connectivity between all devices in the network

Addressing Table
Device..........Interface..........Address.............Subnet Mask.........Default Gateway
HQ..................Fa0/0..........................................................................n/a
......................Fa0/1..........10.10.10.65.........255.255.255.248...............n/a
S2..................VLAN1
NetAdmin..........NIC
H1................... NIC............preconfigured.......preconfigured.........preconfigured
NOTE: The initial network has some errors. To aid in configuring and verifying the devices as well as troubleshooting the existing errors, use a printed version of these instructions to fill in the missing address information in the table during Step 1.

Step 1: Determine the IP Addressing Scheme.
Design an addressing scheme and fill in the Addressing Table based on the following requirements:
a.     Subnet the address space 10.10.10.0/24 to provide 40 host addresses for LAN 1 while wasting the least amount of address space.
b.    Assign the first available subnet to LAN 1.
c.     Assign the lowest (first) host address in this subnet to the Fa0/0 interface on HQ.
d.    Assign the second address in this subnet to the VLAN 1 interface on S2.
e.     Assign the highest (last) host IP address in this subnet to NetAdmin.

Step 2: Configure HQ.
a.     Configure HQ with these basic parameters:
         Use HQ as the router name.
         Use class as the encrypted password for privileged EXEC mode.
         Require password-protected logins for the console line.  Use cisco as the password.
         Require password-protected logins for the vty lines.  Use cisco as the password.
         Configure the banner message-of-the-day as Unauthorized access is prohibited.
b.    Configure the two Fast Ethernet interfaces:
         Configure the router interfaces according to your completed Addressing Table.
         Configure each interface with a description.
c.     Close the terminal window after completing the router configuration.

Step 3: Configure S2 and Verify Connectivity.
a.     Remove the console connection between NetAdmin and HQ.
b.    Connect NetAdmin to the S2 console port.
c.     Configure S2 with these basic parameters:
         Use S2 for the switch name.
         Use class as the encrypted password for privileged EXEC mode.
         Require password-protected logins for the console line.  Use cisco as the password.
         Require password-protected logins for the vty lines.  Use cisco as the password.
         Configure the banner message-of-the-day as Unauthorized access is prohibited.
d.    Configure interface VLAN 1.
e.     Configure the default gateway.
f.     Test that S2 is able to ping the default gateway.

Step 4: Configure and Verify NetAdmin Addressing.
a.     Use the IP addressing you determined in Step 1 and configure NetAdmin with the correct addressing.
b.    Test that NetAdmin is able to ping the default gateway.

Step 5: Verify and Troubleshoot End-to-End Connectivity.
Verify that NetAdmin is able to ping H1. If the ping fails, locate and correct any errors. For example, make sure H1 is configured correctly with appropriate addressing for the subnet it belongs to.

Succesuri! O intrebare: daca nu ai dat pe la cursuri, de ce te-ai mai inscris la CCNA?

_Orpheus, on 17th July 2012, 13:07, said:

@ Orpheus - LIKE

Am fost la toate cursurile, dar s-a facut teorie... parte practica a zis ca o sa facem mai mult la CCNA 2 si CCNA 3

Cu parere de rau, dar n-ai nicio sansa sa termini CCNA 2 si CCNA 3 daca nu stii sa faci asemenea laboratoare.

Degeaba te duci la toate laboratoarele si cursurile daca nu pui mana sa lucrezi nu rezolvi nimic, nu intelegi din prima la laboratoare si daca intelegi trebuie sa lucrezi ca sa iti intre in reflex, eu am termina ccna1,2,3 si ma apuc de 4, si la inceput am fost foarte descurajat pentru ca nu reuseam sa inteleg de la cursuri, asa ca am pus mana si am facut exercitii acasa in PT si invatat dupa cursuri si asa am reusit sa termin si sa ajung la 4.